/ HOME / / ABOUT US / / GO SHOPPING! / / RACES / / BEGINNER'S CORNER / / COACH'S CORNER / CLASSIFIEDS / / TRAINING ROUTES / / LINKS / /SITE MAP/ / RETURNS/ / PURCHASE METHODS /

 
 

 Click buggy to View Shopping Cart
 

SuperWing  $114.99  *NEW*

Rear carriers should not interfere with the air on the rider’s back, but instead fill in the turbulence ‘hole’ behind the riders posterior, thereby reducing the rider’s drag  (which accounts for 64% of energy used on a racing bicycle). XLab positioned the carrier in the Wind Tunnel to 'draft' behind the rider causing no extra drag.

One of the key features invented by Xlab is the multiple mounting holes for the saddle rail clamps. One position sets the bottle cages close to vertical and others incline the cages for rider preference. Because of it's past success, Xlab has kept the same feature in the Xlab Super Wing for customizing the installation.  In addition, there are 4 sets of holes for the lower cage bolts which with the front holes provides a total of 12 different cage angle positions.

Without hardware weighs: 85g

 

Torpedo Mount  $52.99  *NEW*
  • Horizontal NOT tilted up 18 degrees like others
  • Easy install/removal. No tools required
  • Clear of Steerer cap for computer mount
  • Uses non-stretch polyester straps
  • 5X more adjustable than others
  • Ideal for 20km/40km TT/Tri
  • No drag penalty
  • Front area of bottle 68% less than most other bottles
  • Carbon fiber 25g weight
  • 4 straps with silicone grip adjust to aerobar width
  • Fits bars 9-14 cms apart. Centre to centre
  • 1 1/2" fore & aft adjustment of cage on mount
  • Use Xlab Torpedo Cage for lowest drag set up.  For poor road surfaces or steep hills use Xlab Chimp Cage

 

Torpedo Bottle Cage  $54.99  *NEW*
  • Ideal for 20 km, 40km TT/Tri
  • Lowest drag of any front system
  • Only 7"2 Frontal Area 68% less than most others
  • 25g Weight
  • Use Chimp cage for bumpy/hilly roads
  • Mounts ideally on the Torpedo Front Mount

 

Aqua-Shot 24oz Bottle  $9.99  *NEW*
  • Faster drinking while racing or training
  • No valve to pull with teeth
  • Squeeze and squirt leak proof valve
  • High flow-rate for saving time
  • Taste free, BPA Free Polyethylene
  • Clear with calibrations every 4ozs
  • 70 grams
  • 24 oz

 

Carbon Sonic Wing for Cervelo™ P3C & P2C  $159.99 

The CARBON SONIC has a choice of 3 different angles when attaching to the seat post. The cages have a forward lowest drag position which sets the bottles close to the seat, or a position 1inch (25mm) further back for triathletes that like to sit off the back of the saddle when climbing.
There also a variety of bottle cage angles. To add to the fun, you can even invert the carrier for a further 15 positions if you like.
The Carbon Sonic comes complete with it’s own CO2 and INFLATOR holder , known as the Sonic Nut.  BECAUSE the carrier fits on the seat post we have not discovered any seats that you cannot use including the long Fizik, ISM, SMP, Selle Italia, Selle San Marco, Terry and others.  The chassis only weighs a miniscule 49 grams. It is made of aircraft grade High Modulus Carbon Fiber.  The screws for the bottle cages and the mounting screws to attach to the seat post are all TITANIUM.  We only use 6AL-4V grade 5 titanium as it has a tremendous Tensile Strength of 130 Ksi.  The CARBON SONIC weighs in at 28 grams lighter than the alloy Sonic Wing.

 

Sonic Wing for Cervelo™ P3C & P2C  $67.99 

Cervelo™ Specific Alloy Rear Hydration Carrier. You know those mysterious two holes in a Cervelo™ seatpost? Well, this Carrier will fit in there, a nice tight fit. Is compatible with the Cervelo™ P3Cs and P2C's.  Can be inverted for a lower position on the saddle, or keep it upright for a low drag higher position.  Has 30 different positions available, so that you can have a custom fit position that is both comfortable and aerodynamic. 3 different carrier angles and 5 different bottle angles for each position.  When installed in the high position, air flows cleanly around the aero seat post. The narrow 5/8" Sonic with open back for air to exit, can save 13 seconds per kilometer in the high position.  CNC machined from US aircraft grade structural alloy.  Has clearance for Fizik saddles.  Antisway design: compact dual stabilizers, energy saving. Easy installation.  Includes 1 pair of Xstraps and 2 Anti-Drag Discs - Covers spare hole in seatpost for a more aerodynamic ride.

Please note: Black Sonic Wing is available (not shown in photo)

 

Carbon Wing  $159.99 

New from XLab comes the much anticipated Carbon Wing.  The Carbon Wing carries 2 water bottles, tire bag or Kona bag, Mini bag in top, 2 CO2's on X-Nut & Nanoflator on X-Nut.  Includes Carbon Wing, bag straps & installation hardware.

Options (sold separately): 2 - XLab bottle cages, Mini bag, Tire bag, Kona bag, 2 CO2's, Nanoflator, X-Nut.

 

X-Straps  $12.99

Designed for use with the Mini Wing or Flatwing. Holds your spare tires or tubes securely. Clean installation that utilizes a quick release Velcro system. Never be without your spares. One pair holds one tire or 2 tubes. Can fit two pairs on Mini Wing or Flatwing. Mounts with water bottle cage screws.

 

X-Nut   $16.99

An excellent way to hold your Xlab CO2 cartridges and Xlab Nanoflator or Speed Chuck. Mounts securely to the rear of the Carbon Wing, Saddlewing or Flatwing. Makes inflating tires a snap during training rides or out on the race course. Holds up to two Xlab CO2 cartridges. Made in the USA. Color Black. Mounting Hardware included.  19g

 

Sonic Nut   $17.99 

An excellent way to hold your Xlab CO2 cartridges and Xlab Nanoflator. Mounts securely to the rear of the Sonic Wing. Makes inflating tires a snap during training rides or out on the race course. Holds up to two Xlab CO2 cartridges. Made in the USA.  Mounting Hardware and assembly instructions included.  16g

 

 
 

X-Nanoflator  $12.99

For rapid CO2 inflation.  Stored on the X-Nut male threaded protrusion or in the Xlab mini bag on the Xlab carbon wing.  Simply screw on a threaded CO2 cartridge & push end onto valve stem.  36g

 

Gorilla Carbon Cage  $59.99

The Gorilla helps prevent bottles ejecting from cages on bumpy roads, mountain bikes and saddle-mounted water bottle carriers. The cage has over 2X the gripping force of conventional carbon cages due to the 6 high shouldered carbon gripping fingers, tall retention tab at the top and thicker carbon. The Gorilla cage will fit on any standard cage mounts.  Weighs 38g. 

 

Gorilla Carbon Cage  $59.99

The Gorilla helps prevent bottles ejecting from cages on bumpy roads, mountain bikes and saddle-mounted water bottle carriers. The cage has over 2X the gripping force of conventional carbon cages due to the 6 high shouldered carbon gripping fingers, tall retention tab at the top and thicker carbon. The Gorilla cage will fit on any standard cage mounts.  Weighs 38g. 

 

Chimp Carbon Cage  $59.99

Quite often Triathlon framesets have smaller frame triangles and shorter head tubes in an effort to make the frames more aerodynamic. This results in having to pull the water bottle somewhat sideways in order to get it out of the bottle cage. Most current cages on the market make bottle extraction difficult.  The engineers at XLAB have a cage that grips very well over bumpy surfaces but also has a special cut off angle of 30 degrees which testing has proved is the optimum angle in Tri framesets. It is super quick to get the bottle out of the cage.
The cage features stiff bottom lip to support large bottles, stiff upper tab to retain bottles in the cage and slots in the back to provide vertical adjustment on the frame.  Made with the same high temperature and pressure process as the successful Gorilla rear cage and in extra stiff carbon.  The 6 arm design and graphics match the Gorilla so you can now have a consistent bottle cage design on your racing machine but with cages designed for each specific purpose. Use Gorilla Cage for rear hydration carriers.

 

X-Mini Bag  $18.99

This mini bag can mount on an Xlab Carbon Wing or use as a small tool bag.  Constructed of tough Cordura 500 denier.  Weighs 40g

 

X-Tire Bag  $23.99

Have you been using electrical tape for holding your spare tire or tubes?  Problem solved.  Has long velcro straps to strap around the Cervelo seatpost.   This tough bag can store a 700c x 22mm tubular, or a couple of tubes and other items, and fits under the Xlab Carbon Wing or Sonic Wing. Keeps your tires or tubes safe from damaging UV light.  Weighs 80g Length: 6.5"

 

Kona Bag  $31.99

The Kona bag sits beneath the Carbon Wing & can easily carry tubulars & other items, or two tubulars. It has a main pocket & two zippered side pockets.  Weighs 86 g

 

Daylight Training Strobe Light  $23.99

Inspired by dozens of triathletes who have been injured while training, Xlab’s chief guru set a goal to introduce a Daylight Training Strobe with 5 bright LEDs, a 270 degree visibility, weighing under 35 grams. Another Xlab World’s first. ‘Don’t be seen without it.

 
Features
  • 5 Super BRIGHTLEDs
  • Up to 270° Visibility
  • Modes BLINKING, CONSTANT, SWEEP, RANDOM
  • Mounts on ALL XLAB WINGS and round seat posts
  • ONLY 31 Grams excl. Batteries
  • Water Resistan
  • AAA Batteries included
  • Seen up to 2000 FEET (600m)
  • Runtime from 250 HRS (Random) to 70 HRS 9Steady)
  •  

     

    Ti-Lite Kit (Sonic Wing Kit)  $37.99

    As if XLAB’s rear carriers were not light enough, XLAB's crazy engineers have come up with Titanium lightening kits for their SONIC WINGS.  XLAB uses only top quality 6AL-4V Grade 5 titanium and includes a sachet of Ti-Prep lube.  The kits replace the steel screws in the standard product.
    Grade 5 titanium has a Tensile Strength of 130Ksi, which far exceeds the design requirements. Which is why aircraft designers select them. The SONIC WING KIT replaces the four 5mm and two 6mm steel screws for a great weight saving of 13g. Why carry excess weight when you don’t have to?

     

    Ti-Lite Kit (Super Wing or Carbon Wing Kit)  $44.99

    As if XLAB’s rear carriers were not light enough, XLAB's crazy engineers have come up with Titanium lightening kits for their Super and Carbon WINGS.  XLAB uses only top quality 6AL-4V Grade 5 titanium and includes a sachet of Ti-Prep lube.  The kits replace the steel screws in the standard product.
    Grade 5 titanium has a Tensile Strength of 130Ksi, which far exceeds the design requirements. Which is why aircraft designers select them. The SUPER and CARBON WING KIT
    replaces the eight 5mm steel screws for a nice weight saving of 12g. Now the best can get even lighter!

     
     Click buggy to View Shopping Cart